[HELP] X96mini q6x v2.2 17355 bricked

[qontol]

[mention]kokito0[/mention] so you're serious about microscope because of D0 pin , it kills my passion to repair my x96mini.
i just prepare the cables, solder, breaking my USB sdcard reader, secure it with tape...
but after review the D0 pin, i take a broom and clean up the dirt I made

anyway would you mind share the password for the dump file ? in case if i found another way to restore the dump. i found this article interesting https://www.slatedroid.com/topic/111538 ... 6mx-by-cxz , i tried some feature like reboot, check connectivity, it all works, i want to try restore the bootloader but i don't have the working bootloader for this x96mini, will there a bootloader in the dump file you share ?

image.png

[kokito0]

Yes the D0 is very small and need to clear with scalpel to see where it is.
password: 84374539601

[kokito0]

, i tried some feature like reboot, check connectivity, it all works, i want to try restore the bootloader but i don't have the working bootloader for this x96mini, will there a bootloader in the dump file you share ?

Yes with this dump you can to restore bootloader

[kodov]

@kokito0
Tell me if I can upload your Dump https://mega.nz/file/PsUjGYgK#nBfJ5_EE9 ... rR9i82MZiA using the programmer or ISP method ?

[maan_mani12]

Hello, i have tv box x96mini with board q6x v2.2 17355
It's bricked and when plug power only red light and no screen.
i try to flash with usb burnnig tools many firmware but result it's this error " [0x10103005]Romcode/Initialize DDR/Download buffer/Read item data failed "
when i connect with cable male to male and pc automatic recognize the box ( no need to hold av button)
Can anyone help me ?and which firmware is the right one for this box ?

Have you find any solution of it... My device also brick and show same error

[maan_mani12]

Hello, i have tv box x96mini with board q6x v2.2 17355
It's bricked and when plug power only red light and no screen.
Have you find any solution of it... My device also brick and show same error
i try to flash with usb burnnig tools many firmware but result it's this error " [0x10103005]Romcode/Initialize DDR/Download buffer/Read item data failed "
when i connect with cable male to male and pc automatic recognize the box ( no need to hold av button)

Can anyone help me ? and which firmware is the right one for this box ?

[maan_mani12]

@kokito0
Tell me if I can upload your Dump https://mega.nz/file/PsUjGYgK#nBfJ5_EE9 ... rR9i82MZiA using the programmer or ISP method ?

When i convert imgc to img file it becomes too large file about 15 gb... And not able to flash... Plz help me

[alvinseliang]

I unbrick the box with this very hard method....

Hello @kokito0 , are you sure if i do what u have successful done to your q6x 13775 board.. it come to same result? I want to try it..

Thanks before

[alvinseliang]

Hello.. @kokito0 i still cannot boot even i success dump your bootloader (imgc) with Hdguru (100% copied to nand after i format it -fat32)..

Is there i missed to do when it was done copied?

Please tell me what i must to do next?

[vlado777777]

Hi @kokito0 , i need this to if you don't mind

Can you mark (d0,clk,cmd and ground) where each wire goes on PCB ?

also do you using the dump firmware from this post ?

@kokito0 https://drive.google.com/u/0/uc?id=1nqQ ... t=download

no this is twrp dump
this is original dump ==> https://mega.nz/file/PsUjGYgK#nBfJ5_EE9 ... rR9i82MZiA

The link is dead - is someone have the dump?