bumerc
more
level2\recovery\ramdisk\etc
Merged: T95Z Plus 3GB+32GB DISCUSSION
-
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
Your remote control has a hard coded code (manufacturer / custom code) from the manufacturer, this must match the factory_code in the remote.conf. Unfortunately it is also a wrong file. Your factory_code is „0x40400001“.
-
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
[mention]Pyrysid[/mention]
Go to this page and search for the right remote.conf file. Important for you is the right factory code => factory_code = 0x40400001. Make sure the remote.conf file has the old configuration format (remote.conf files with only one factory_code.) The codes - custom_begin,
factory_infcode = x, custom_end should not be used). Furthermore, the uboot must have the appropriate power_key code, so now switching on works. Customizing the DTB file would be an alternative method, but very time-consuming and less user-friendly.
Go to this page and search for the right remote.conf file. Important for you is the right factory code => factory_code = 0x40400001. Make sure the remote.conf file has the old configuration format (remote.conf files with only one factory_code.) The codes - custom_begin,
factory_infcode = x, custom_end should not be used). Furthermore, the uboot must have the appropriate power_key code, so now switching on works. Customizing the DTB file would be an alternative method, but very time-consuming and less user-friendly.
-
- Posts: 9
- Joined: Tue Oct 23, 2018 6:13 am
bumerc, sorry may be my fail
try new level2\recovery\ramdisk\etc only have 0x40400001
my original firmware http://www.mediafire.com/file/f3ssbt3x6 ... DR3-2G.rar
I can run the tvbox, the first time I can put the tvbox to sleep and wake it up, but after the original remote does not work, it can only use it to wake up the tvbox. Air mouse g10 is fully operational, but I can't wake up the tvbox. Tell me what I have to do to make Air mouse g10 work at least? Thanks for the help.
try new level2\recovery\ramdisk\etc only have 0x40400001
my original firmware http://www.mediafire.com/file/f3ssbt3x6 ... DR3-2G.rar
I can run the tvbox, the first time I can put the tvbox to sleep and wake it up, but after the original remote does not work, it can only use it to wake up the tvbox. Air mouse g10 is fully operational, but I can't wake up the tvbox. Tell me what I have to do to make Air mouse g10 work at least? Thanks for the help.
You do not have the required permissions to view the files attached to this post.
-
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
Ok, I have understood your problem now.Pyrysid wrote: ↑Tue Feb 12, 2019 3:42 pm bumerc, sorry may be my fail
try new remote.conf level2\recovery\ramdisk\etc only have 0x40400001
my original firmware http://www.mediafire.com/file/f3ssbt3x6 ... DR3-2G.rar
I can run the tvbox, the first time I can put the tvbox to sleep and wake it up, but after the original remote does not work, it can only use it to wake up the tvbox. Air mouse g10 is fully operational, but I can't wake up the tvbox. Tell me what I have to do to make Air mouse g10 work at least? Thanks for the help.
1. If the original remote control does not work after the sleep mode, you can re-enable it with this simple command:
Code: Select all
start remotecfg
2. I'm making a small uboot update that will allow you to wake up via Air Mouse, but you'll need to test it.
EDIT:
I tried to wake the box via Air Mouse, it works, but unfortunately only as long as the USB port remains energized. After a few seconds (in sleep mode) the USB power is gone and the BT_WAKEUP stops working. That's the current status.
-
- Posts: 3
- Joined: Mon Feb 04, 2019 11:22 pm
I have no idea how to do this? Is there a tutorial?bumerc wrote: ↑Fri Feb 08, 2019 6:11 am [mention]islandfever[/mention]
You have a DDR3-1600 RAM memory and have apparently installed LPDDR3 or DDR4 version ?? You can only use the Maskrom mode, hold down the eMMC pins 29-30 for about 2 sec. and flashing the normal DDR3 version. (atvXperience_S912_V2H_FINAL.img, or one of the earlier releases)
-
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
viewtopic.php?f=3&p=4303#p4303islandfever wrote: ↑Wed Feb 13, 2019 3:23 pmI have no idea how to do this? Is there a tutorial?bumerc wrote: ↑Fri Feb 08, 2019 6:11 am [mention]islandfever[/mention]
You have a DDR3-1600 RAM memory and have apparently installed LPDDR3 or DDR4 version ?? You can only use the Maskrom mode, hold down the eMMC pins 29-30 for about 2 sec. and flashing the normal DDR3 version. (atvXperience_S912_V2H_FINAL.img, or one of the earlier releases)
-
- Administrator & Developer
- Posts: 1263
- Joined: Mon Jun 11, 2018 11:58 pm
- Has thanked: 192 times
- Been thanked: 434 times
- Contact:
1. V2FF Does, V2H is an optional build.
2. Use Aptoide TV, v2FF comes preinstalled with it
3. Idk what canal digital is, explain plox
4. magisk not installing - what error?
BE NICE, BE RESPECTFUL
RESPECT THE MODERATORS
PM ONLY WHEN IMPORTANT
ENJOY! My Devices:
X96 Mini, A95X Pro, H96 Pro Stick, A95X Max
RESPECT THE MODERATORS
PM ONLY WHEN IMPORTANT
ENJOY! My Devices:
X96 Mini, A95X Pro, H96 Pro Stick, A95X Max