[QUESTION] X905W 2/16Gb after the ver.4 installed the bootloader has been disabled.
-
em3ka
- Moderator
- Posts: 1835
- Joined: Sun Jul 15, 2018 11:43 am
- Has thanked: 108 times
- Been thanked: 370 times
Recovery mode, use the pre-installed Power Menu app and choose "Reboot to recovery" option.
v4.0 firmware upgrade:
viewtopic.php?f=2&t=2451&p=13534&#p13533
-
kostas
- Posts: 5
- Joined: Mon Mar 22, 2021 4:59 pm
Reboot to recovery" option yes i tried but nothing happens, this happened after I used the option "safe mode" The problem is when I choose any reboot mode the device is not booting. For a boot i need to pwer off and on again but no bootloader appears by pressing reset button continuously before put the power jack on the power socket.
-
bumerc
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
v4 is no longer available, you have installed the wrong versionafter the ver.4 installed the bootloader has been disabled.
https://blog.danman.eu/bricking-and-unb ... -x96-mini/
-
kostas
- Posts: 5
- Joined: Mon Mar 22, 2021 4:59 pm
ok, correct I have installed a version which caused a reset button issue. So, my question how can I initiate again the reset button, is it possible over su command prompt by some commands? or is there a apk program which can improve this situation? I need a solution regarding this issue.
-
bumerc
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
Read the blog above and install v4.2.1 or stock ROMkostas wrote: ↑Tue Mar 23, 2021 8:38 am ok, correct I have installed a version which caused a reset button issue. So, my question how can I initiate again the reset button, is it possible over su command prompt by some commands? or is there a apk program which can improve this situation? I need a solution regarding this issue.
-
bumerc
- Administrator & Developer
- Posts: 1551
- Joined: Tue Oct 02, 2018 6:19 pm
- Has thanked: 211 times
- Been thanked: 334 times
-
Seva_Vice
- Posts: 1
- Joined: Sat Apr 17, 2021 12:16 pm
Hi everyone!
I faced a similar problem. I flashed ATVX 4.1 via UBT. It starts but stops at language selection stage. Whatever I choose "Set-up with a smartphone" or "Skip" option, it gives me a black screen for sometime, and then goes back to language selection. The box does not react to Reset button, and I'm aware of that. So now it is not a brick, however it is a useless piece of something which cannot be call a smart TV box. There is no way to flash it via UBT, as the Reset button in inactive, and no way to do anythind using SD-card for the same reason. It does not go further in the set-up menu either, so no way I can access Power Menu. Is there anything which can be done to fix the box?
I faced a similar problem. I flashed ATVX 4.1 via UBT. It starts but stops at language selection stage. Whatever I choose "Set-up with a smartphone" or "Skip" option, it gives me a black screen for sometime, and then goes back to language selection. The box does not react to Reset button, and I'm aware of that. So now it is not a brick, however it is a useless piece of something which cannot be call a smart TV box. There is no way to flash it via UBT, as the Reset button in inactive, and no way to do anythind using SD-card for the same reason. It does not go further in the set-up menu either, so no way I can access Power Menu. Is there anything which can be done to fix the box?